收藏本站
9. Read Operations
Read operations are initiated the same way as write operations with the exception that the
read/write select bit in the device address word is set to “1”. There are three read operations:
current address read, random address read, and sequential read.
CURRENT ADDRESS READ: The internal data word address counter maintains the last
address accessed during the last read or write operation, incremented by one. This address
stays valid between operations as long as the chip power is maintained. The address “roll over”
during read is from the last byte of the last memory page, to the first byte of the first page.
Once the device address with the read/write select bit set to “1” is clocked in and acknowledged
by the EEPROM, the current address data word is serially clocked out. The microcontroller does
not respond with an input “0” but does generate a following stop condition (see Figure 9-1 ).
Figure 9-1.
Current Address Read
RANDOM READ: A random read requires a “dummy” byte write sequence to load in the data
word address. Once the device address word and data word address are clocked in and
acknowledged by the EEPROM, the microcontroller must generate another start condition. The
microcontroller now initiates a current address read by sending a device address with the
read/write select bit high. The EEPROM acknowledges the device address and serially clocks
out the data word. The microcontroller does not respond with a “0” but does generate a following
stop condition (see Figure 9-2 ).
Figure 9-2.
Random Read
Note:
* = DON’T CARE bit
SEQUENTIAL READ: Sequential reads are initiated by either a current address read or a ran-
dom address read. After the microcontroller receives a data word, it responds with an
acknowledge. As long as the EEPROM receives an acknowledge, it will continue to increment
the data word address and serially clock out sequential data words. When the memory address
limit is reached, the data word address will “roll over” and the sequential read will continue. The
10
AT24C128B
5296A–SEEPR–1/08
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
AT24C128C-XHM-B IC EEPROM 128KBIT 400KHZ 8TSSOP
AT24C128Y1-10YU-1.8 IC EEPROM 128KBIT 400KHZ 8MAP
AT24C164-10SU-1.8 IC EEPROM 16KBIT 1MHZ 8SOIC
AT24C16AY6-10YH-1.8 IC EEPROM 16KBIT 400KHZ 8DFN
AT24C16BY6-YH-T IC EEPROM 16KBIT 1MHZ 8DFN
AT24C256BW-SH-T IC EEPROM 256KBIT 1MHZ 8SOIC
AT24C256C-XHL-B IC EEPROM 256KBIT IND 8TSSOP
AT24C32AY6-10YH-1.8 IC EEPROM 32KBIT 400KHZ 8DFN
相关代理商/技术参数
AT24C128C1-10CC 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:2-Wire Serial EEPROMs
AT24C128C1-10CC-1.8 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:2-Wire Serial EEPROMs
AT24C128C1-10CC-2.7 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:2-Wire Serial EEPROMs
AT24C128C1-10CI 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:2-Wire Serial EEPROMs
AT24C128C1-10CI-1.8 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:2-Wire Serial EEPROMs
AT24C128C1-10CI-2.7 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:2-Wire Serial EEPROMs
AT24C128C-CUM-T 制造商:Atmel Corporation 功能描述:
AT24C128C-MAHM-T 功能描述:电可擦除可编程只读存储器 SERIAL 电可擦除可编程只读存储器 128K (16K x 8) 2WIRE 1.7V RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8